Persona: Agustina Tejerizo, Beatriz De
Cargando...
Dirección de correo electrónico
ORCID
0000-0003-0149-6928
Fecha de nacimiento
Proyectos de investigación
Unidades organizativas
Puesto de trabajo
Apellidos
Agustina Tejerizo
Nombre de pila
Beatriz De
Nombre
5 resultados
Resultados de la búsqueda
Mostrando 1 - 5 de 5
Publicación Experimental study of magnesium drilling based on the surface quality(Elsevier, 2019) Berzosa Lara, Fernando; Agustina Tejerizo, Beatriz De; Rubio Alvir, Eva María; Marín Martín, Marta MaríaNowadays, the use of magnesium and its alloys for transport applications is based on the combination of high mechanical properties and low density. In general, the machinability of these materials is considered to be good. Nevertheless, it has been reported that the machining of these alloys involves some critical problems regarding their tendency to be flammable at high temperatures and consequently, there is a risk of chip ignition in the working area during the process. This fact is especially critical when the size of chips is reduced. In this study, the influence of cutting conditions on surface roughness, in terms of Ra, obtained by drilling of magnesium alloy (AZ91D-F) was carried out. A factorial design 2 4 was employed for the planning of the drilling tests. The factors considered were the feed rate (0.05 and 0.2 mm/r), cutting speed, 40 and 60 m/min, the type of tool, in particular, the point angle of 118º and 135º, and the cooling system, Dry conditions and MQL (Minimum Quantity Lubrication) system. As main conclusions it can be affirmed that improved surface roughness is obtained with the cutting conditions selected in this study. Furthermore, at 0.05 mm/r and 40 m/min the use of tools with a point angle of 135º provides lower values of Ra than the tool of 118º point angle. Slightly lower values of Ra are obtained with tools of 118º point angle at 0.2 mm/r and 60 m/min.Publicación Tool Selection in Drilling of Magnesium UNSM11917 Pieces under Dry and MQL Conditions based on Surface Roughness(Elsevier, 2017) Berzosa Lara, Fernando; Agustina Tejerizo, Beatriz De; Rubio Alvir, Eva MaríaNowadays, the use of lighter materials for transportation purposes is still a challenge; especially in the aeronautical and aerospace sectors. The use of certain materials, such as magnesium alloys which have exceptional mechanical properties relative to density as structural materials, allows a remarkable reduction of weight. These alloys have significant challenges in machining. On the one hand, their use with water-based lubricants can produce flammable hydrogen atmospheres and, on the other hand, the operational parameters can produce tiny chips which, at high temperature, could burn. Regarding the tools, drills are the most used ones in drilling operations; manufacturers do not always take in consideration magnesium alloys. This is why, sometimes, the data from other types of similar alloys need to be extrapolated. This work shows an experimental study about the drilling of magnesium pieces based on surface roughness. The main goal is to determine the tools that best suit the requirement of surface roughness for this type of operations, which, for the aeronautical sector, is from 0.8 to 1.6 μm. The tests have been conducted under different cutting conditions, using several types of tools and two sustainable lubrication systems. In particular, dry machining and minimum quantity of lubrication (MQL) system have been used. A design of experiments (DOE) has been used to optimize the resources. The average roughness, Ra, has been selected as a response variable. The roughness values obtained are lower than 0.9 μm (namely, from 0.13 μm to 0.87 μm); so, it is possible to increase some of the parameter values, in order to improve the productivity, without they go outside the established limits. The results have been analyzed using the analysis of variance (ANOVA) method. A model for estimating the expected surface roughness in terms of the Rae, has been developed.Publicación Tool Selection in Drilling of Magnesium UNSM11917 Pieces under Dry and MQL Conditions based on Surface Roughness(Elsevier, 2017) Berzosa Lara, Fernando; Agustina Tejerizo, Beatriz De; Rubio Alvir, Eva MaríaNowadays, the use of lighter materials for transportation purposes is still a challenge; especially in the aeronautical and aerospace sectors. The use of certain materials, such as magnesium alloys which have exceptional mechanical properties relative to density as structural materials, allows a remarkable reduction of weight. These alloys have significant challenges in machining. On the one hand, their use with water-based lubricants can produce flammable hydrogen atmospheres and, on the other hand, the operational parameters can produce tiny chips which, at high temperature, could burn. Regarding the tools, drills are the most used ones in drilling operations; manufacturers do not always take in consideration magnesium alloys. This is why, sometimes, the data from other types of similar alloys need to be extrapolated. This work shows an experimental study about the drilling of magnesium pieces based on surface roughness. The main goal is to determine the tools that best suit the requirement of surface roughness for this type of operations, which, for the aeronautical sector, is from 0.8 to 1.6 μm. The tests have been conducted under different cutting conditions, using several types of tools and two sustainable lubrication systems. In particular, dry machining and minimum quantity of lubrication (MQL) system have been used. A design of experiments (DOE) has been used to optimize the resources. The average roughness, Ra, has been selected as a response variable. The roughness values obtained are lower than 0.9 μm (namely, from 0.13 μm to 0.87 μm); so, it is possible to increase some of the parameter values, in order to improve the productivity, without they go outside the established limits. The results have been analyzed using the analysis of variance (ANOVA) method. A model for estimating the expected surface roughness in terms of the Rae, has been developed.Publicación Estudio de la fuerza de avance y la circularidad de los agujeros en el taladrado criogénico de materiales compuestos con aramida(['Universidad Nacional de Educación a Distancia (España)', 'Universidad Politécnica de Madrid. Departamento de Ingeniería Mecánica'], 2022) Rodríguez Martín, Manuel; Domingo Navas, María Rosario; Ayllón Pérez, Jorge; Agustina Tejerizo, Beatriz DeEl uso de refrigerantes criogénicos en los procesos de mecanizado en los últimos años están teniendo una especial atención, así como su incidencia cuando se usan materiales compuestos, como aquellos reforzados por fibras de aramida o kevlar. Este trabajo analiza los resultados experimentales del taladrado criogénico con nitrógeno líquido en pletinas de aramida, en las fuerzas de avance, los diámetros de los agujeros taladrados y la rugosidad de las paredes, para posteriormente realizar un análisis mediante la metodología de superficie de respuesta (RSM). Este trabajo encuentra que, en el rango de las condiciones de corte empleadas, el diámetro del agujero no depende de la velocidad de rotación de la broca, mientras que la fuerza de avance y la rugosidad son dependientes de la velocidad de rotación y de avance; además aporta resultados que muestran la viabilidad de este proceso a temperaturas inferiores a -150ºC.Publicación Experimental study of magnesium drilling based on the surface quality(Elsevier, 2019) Berzosa Lara, Fernando; Agustina Tejerizo, Beatriz De; Rubio Alvir, Eva María; Marín Martín, Marta MaríaNowadays, the use of magnesium and its alloys for transport applications is based on the combination of high mechanical properties and low density. In general, the machinability of these materials is considered to be good. Nevertheless, it has been reported that the machining of these alloys involves some critical problems regarding their tendency to be flammable at high temperatures and consequently, there is a risk of chip ignition in the working area during the process. This fact is especially critical when the size of chips is reduced. In this study, the influence of cutting conditions on surface roughness, in terms of Ra, obtained by drilling of magnesium alloy (AZ91D-F) was carried out. A factorial design 2 4 was employed for the planning of the drilling tests. The factors considered were the feed rate (0.05 and 0.2 mm/r), cutting speed, 40 and 60 m/min, the type of tool, in particular, the point angle of 118º and 135º, and the cooling system, Dry conditions and MQL (Minimum Quantity Lubrication) system. As main conclusions it can be affirmed that improved surface roughness is obtained with the cutting conditions selected in this study. Furthermore, at 0.05 mm/r and 40 m/min the use of tools with a point angle of 135º provides lower values of Ra than the tool of 118º point angle. Slightly lower values of Ra are obtained with tools of 118º point angle at 0.2 mm/r and 60 m/min.